富士施樂1810出現錯誤004345，紙張設定左下方有感嘆號
更新時間：2024/11/19 9:22:21,view:4234施樂打印機1810蘇州施樂打印機售后服務中心客服熱線69616769，蘇州施樂售后電話，施樂售后網點，
富士施樂1810 出現錯誤004345，紙張設定左下方有感嘆號 
技術交流平臺 過眼云煙 2016-7-29 15:35:32
施樂s1810出現004345代碼，紙張設定下方出現感嘆號。望高手盡快解答啊。
技術交流平臺 過眼云煙 2016-7-29 15:38:09
施樂s1810出現004345代碼，紙張設定下方出現感嘆號。望高手盡快解答啊。
技術交流平臺 維修師傅 2016-7-30 7:20:39
紙張類型設置不正確，重新設定即可。
小馬 2017-6-14 22:32:42
施樂復印機顯示004一345代碼
MCU/ HVPS通訊故障。解決方案：1、檢查5 VDC從P/ J574-5至P/ J574-4對HVPS控制PWB2、 斷開 P/ J574.Is有5 VDC從第j574-5到J574-43、檢查電線從J411-5到J574-5的對地短路4、切斷電源，并檢查這些電線的斷路或短路接地以下5、HVPS控制電路板P / J574-9到MCU板P / J411-16、HVPS控制電路板P / J574-8到MCU板P / J411-27、HVPS控制電路板P / J574-7到MCU板P / J411-38、HVPS控制電路板P / J574-6到MCU板P / J411-49、檢查開路或P / J411之間的5 VDC電源線連接松動，針腳5和6;和P / J574，針腳5和410、如果這不能解決問題，請更換高壓電源控制電路板和發動機控制板
004-345MCU/HVPS
Communication Fail.SOLUTION:Check 5 VDC from P/J 574-5 to P/J 574- 4 on the HVPS Control PWB 2.Disconnect P/J 574.Is there 5 VDC from J 574-5 to J 574-4 3.Check the wire from J411-5 to J574-5 for a short circuit to ground 4.Switch off the power and check these wires for an open or short circuit to ground for the following: 5.HVPS Control PWB P/J574-9 to MCU PWB P/J411-1 6.HVPS Control PWB P/J574-8 to MCU PWB P/J411-2 7.HVPS Control PWB P/J574-7 to MCU PWB P/J411-3 8.HVPS Control PWB P/J574-6 to MCU PWB P/J411-4 9.Check for open circuit or loose connections in the 5 VDC supply wires between P/J411, pins 5 and 6; and P/J574, pins 5 and 4. 10.If this does not resolve the problem, replace the HVPS Control PWB & Engine control Board
施樂s1810出現004345代碼，紙張設定下方出現感嘆號。望高手盡快解答啊。
施樂s1810出現004345代碼，紙張設定下方出現感嘆號。望高手盡快解答啊。
紙張類型設置不正確，重新設定即可。
施樂復印機顯示004一345代碼
MCU/ HVPS通訊故障。解決方案：1、檢查5 VDC從P/ J574-5至P/ J574-4對HVPS控制PWB2、 斷開 P/ J574.Is有5 VDC從第j574-5到J574-43、檢查電線從J411-5到J574-5的對地短路4、切斷電源，并檢查這些電線的斷路或短路接地以下5、HVPS控制電路板P / J574-9到MCU板P / J411-16、HVPS控制電路板P / J574-8到MCU板P / J411-27、HVPS控制電路板P / J574-7到MCU板P / J411-38、HVPS控制電路板P / J574-6到MCU板P / J411-49、檢查開路或P / J411之間的5 VDC電源線連接松動，針腳5和6;和P / J574，針腳5和410、如果這不能解決問題，請更換高壓電源控制電路板和發動機控制板
004-345MCU/HVPS
Communication Fail.SOLUTION:Check 5 VDC from P/J 574-5 to P/J 574- 4 on the HVPS Control PWB 2.Disconnect P/J 574.Is there 5 VDC from J 574-5 to J 574-4 3.Check the wire from J411-5 to J574-5 for a short circuit to ground 4.Switch off the power and check these wires for an open or short circuit to ground for the following: 5.HVPS Control PWB P/J574-9 to MCU PWB P/J411-1 6.HVPS Control PWB P/J574-8 to MCU PWB P/J411-2 7.HVPS Control PWB P/J574-7 to MCU PWB P/J411-3 8.HVPS Control PWB P/J574-6 to MCU PWB P/J411-4 9.Check for open circuit or loose connections in the 5 VDC supply wires between P/J411, pins 5 and 6; and P/J574, pins 5 and 4. 10.If this does not resolve the problem, replace the HVPS Control PWB & Engine control Board
熱門圖文資料