佳能2002出現e003一0000代碼故障
更新時間：2025/2/3 4:07:02,view:430佳能打印機2002蘇州佳能打印機售后服務中心客服熱線69616769，蘇州佳能售后電話，佳能售后網點， 佳能IR2002g提示E000-0000是什么意思, 佳能2002l清e(cuò)0020000, 佳能2002g進入維修模式, 佳能2002ge0000000, 佳能2002g打印一半顏色淺,維修視頻
佳能2002報E0030000如何處理
主要原因 / 癥狀 異常低溫 ( 主熱敏電阻檢測 ) 在達到目標溫度以后的初始旋 轉之中主熱敏電阻檢測的溫度 未達到目標溫度。 對策 檢查定影薄膜單元的,更換定影部件
佳能IR2318L打印機經常出現**0000030000錯誤,需重啟。0002 E002 0000 E003 0000 E007 副熱敏電阻的讀數連續200msec為295℃以上。佳能2002出現e003一0000代碼故障
佳能2002售后技術論壇 UI 2018/10/10 16:30:52 看圖圖
佳能2002售后技術論壇 曹獗棍 2018/10/10 21:32:34 Code E003-0000
Description The main thermistor reading is lower than
140C when paper is moved
Causes The fixing film unit is faulty (i.e., the main thermistor (TH1) has poor contact or has an open circuit; or, the fixing heater is faulty). The main power supply PCB is faulty. The DC controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR.
Remedy
1. State Turn on the power switch, and clear E002/E003. Thereafter, turn off and then on the power switch. Does the fixing heater operate? NO: See “The fixing heater fails to operate.”
2. Wiring Is the wiring from the DC controller PCB to the fixing film unit normal? NO: Correct the wiring.
3. Fixing film unit, DC controller PCB Try replacing the fixing film unit. Is the problem corrected? YES: End. NO: Replace the DC controller PCB.
佳能2002 316807847 2018/2/7 16:35:26 看不到提示
主要原因 / 癥狀 異常低溫 ( 主熱敏電阻檢測 ) 在達到目標溫度以后的初始旋 轉之中主熱敏電阻檢測的溫度 未達到目標溫度。 對策 檢查定影薄膜單元的,更換定影部件
佳能IR2318L打印機經常出現**0000030000錯誤,需重啟。0002 E002 0000 E003 0000 E007 副熱敏電阻的讀數連續200msec為295℃以上。佳能2002出現e003一0000代碼故障
佳能2002售后技術論壇 UI 2018/10/10 16:30:52 看圖圖 佳能2002售后技術論壇 曹獗棍 2018/10/10 21:32:34 Code E003-0000 Description The main thermistor reading is lower than
140C when paper is moved
Causes The fixing film unit is faulty (i.e., the main thermistor (TH1) has poor contact or has an open circuit; or, the fixing heater is faulty). The main power supply PCB is faulty. The DC controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR.
Remedy
1. State Turn on the power switch, and clear E002/E003. Thereafter, turn off and then on the power switch. Does the fixing heater operate? NO: See “The fixing heater fails to operate.”
2. Wiring Is the wiring from the DC controller PCB to the fixing film unit normal? NO: Correct the wiring.
3. Fixing film unit, DC controller PCB Try replacing the fixing film unit. Is the problem corrected? YES: End. NO: Replace the DC controller PCB.
佳能2002 316807847 2018/2/7 16:35:26 看不到提示
熱門圖文