Sharp MXM1204常見故障代碼描述,英文手冊1
更新時間：2024/11/1 6:17:33,view:189sharp打印機SharpMXM1204蘇州sharp打印機售后服務中心客服熱線69616769，蘇州sharp售后電話，sharp售后網點，維修視頻
Code: A0-01
Description:
PCU PWB ROM error
Causes:
The firmware version-up is not completed properly by interruption of the power during the version-up operation, etc. PCU PWB trouble.
Remedy:
Use SIM49-1 to perform the firmware version-up procedure again. Replace the PCU PWB.
Code: A0-02
Description:
SCU PWB ROM error
Causes:
The firmware version-up is not completed properly by interruption of the power during the version-up operation, etc. SCU PWB trouble.
Remedy:
Use SIM49-1 to perform the firmware version-up procedure again. Replace the SCU PWB.
Code: A0-04
Description:
Scanner expansion PWB (ACU) (ACRE) ROM error
Causes:
Scanner expansion PWB (ACU) (ACRE) ROM data error. An error occurs during firmware upgrading for some reasons.
Remedy:
Perform firmware upgrading again.
Code: A0-05
Description:
Scanner expansion PWB (ACU) (ACRE) firmware error
Causes:
Improper firmware A firmware of a different model is installed. A ROM of a different model is installed.
Remedy:
Replace the ROM with a proper one. Write the proper firmware. (Upgrade to the proper firmware.)
Code: A0-10
Description:
MFPC PWB ROM error
Causes:
CTL and the image ROM firmware combination error
Remedy:
Check the firmware combination of CTL and the image ROM.
Code: A0-11
Description:
Firmware version inconsistency (MFP - PCU)
Causes:
Firmware combination error between the MFP and the PCU.
Remedy:
Install the firmware in the all-firmware version-up mode.
Code: A0-14
Description:
Inconsistency between the MFP and the CPU firmware version
Causes:
Combination error between the MFP and the CPU UI firmware version.
Remedy:
Install the firmware in the all-firmware version-up mode.
Code: A0-15
Description:
Incompatible DSK BOOT and program firmware
Causes:
Installation of the normal firmware was performed with a security kit enable.
Remedy:
Stop installation of the normal firmware.
Code: A0-16
Description:
Data error of the energy-saving NIC controller firmware in the SD card
Causes:
SD card trouble. MFPC PWB trouble.
Remedy:
Reinstall the firmware. Replace the SD card. Replace the MFPC PWB.
Code: A0-17
Description:
Inconsistency between the UI data and the CPU firmware version
Causes:
Combination error between the UI contents data and the CPU UI firmware version.
Remedy:
Install the firmware in the all-firmware version-up mode.
Code: A0-20
Description:
Conflict firmware and EEPROM data version (MFP)
Causes:
Inconsistency between the MFP firmware version and the EEPROM data version.
Remedy:
Check the combination of the firmware.
Code: A0-21
Description:
Conflict firmware and EEPROM data version (PCU)
Causes:
Inconsistency between the PCU firmware version and the EEPROM data version.
Remedy:
Check the combination of the firmware.
Code: A0-22
Description:
Conflict firmware and EEPROM data version (SCU)
Causes:
Inconsistency between the SCU firmware version and the EEPROM data version.
Remedy:
Check the combination of the firmware.
Code: C1-01
Description:
Charger cleaner trouble (K)
Causes:
The main charger unit (K) is not installed properly. There is an abnormality in the main charger unit (K). Connector connection trouble of the drum unit (K) hp sensor, the discharge lamp, or the after-transfer discharge lamp. Harness disconnection of the drum unit (K) hp sensor, the discharge lamp, or the after-transfer discharge lamp. hp sensor dirt. Charger cleaner motor (K) trouble. PCU PWB connector connection trouble/PWB trouble.
Remedy:
Use SIM6-4 to check the operation of the charger cleaner. Check disconnection of the main charger unit./ Replace. Check for disconnection of the connector of the drum unit (K) hp sensor, the discharge lamp, and the aftertransfer discharge lamp. Check the harness of the drum unit (K) hp sensor, the discharge lamp, and the after-transfer discharge lamp. (Since the earth wire is common to them, check the three positions.) Clean the hp sensor. Check disconnection of the PCU PWB connector./ Replace PWB. Replace the charger cleaner motor (K).
Code: C1-10
Description:
Main charger trouble (Monochrome)
Causes:
The main charger unit (K) is not installed properly. There is an abnormality in the main charger unit (K). Disconnection of the high voltage PWB connector. Breakage of the high voltage harness. High voltage PWB trouble. PCU PWB trouble.
Remedy:
Check the output of the main charger with SIM8-2. Check disconnection of the main charger./Replace. Check disconnection of the high voltage PWB connector./Replace. Replace the high voltage PWB. Replace the PCU PWB.
Code: C4-20
Description:
Transfer high voltage output trouble
Causes:
Transfer unit abnormality. Transfer unit insertion trouble. TC output harness disconnection, breakage. Transfer unit separation operation trouble. OPC drum abnormality (Does not rotate.) High voltage PWB trouble. PCU PWB trouble. PCU PWB - high voltage PWB harness disconnection, breakage.
Remedy:
Replace the transfer unit. Reinsert the transfer unit. Check or replace the TC output harness. Replace the high voltage PWB. Replace the PCU PWB. Check the harness between the PCU PWB and the high voltage PWB, and replace as needed.
Code: E6-10
Description:
DSPF shading error (Black correction)
Causes:
Installation error of the CCD unit harness. CCD unit trouble. DSPF PWB trouble.
Remedy:
Check the installing state of the harness to the CCD unit. Check the CCD unit. Check the DSPF PWB.
Code: E6-11
Description:
DSPF shading error (White correction)
Causes:
Installation error of the CCD unit harness. Copy lamp lighting trouble. Dirt on the mirror, the lens, or the reference white plate. CCD unit trouble. DSPF PWB trouble. Shading SIM not executed / Shading ROM abnormality.
Remedy:
Check the installing state of the harness the CCD unit. Check the installing state of the harness to the copy lamp unit. Clean the mirror, the lens, or the reference white plate. Check the CCD unit. Check the DSPF PWB.
Code: E6-14
Description:
DSPF CCD-ASIC error
Causes:
DSPF PWB trouble.
Remedy:
Check the DSPF PWB.
Code: E7-01
Description:
MFP image data error
Causes:
Image data transfer error in the MFPC PWB. MFPC PWB trouble.
Remedy:
Check connection of the connector and the harness of the MFPC PWB. Check or replace the MFPC PWB.
Code: E7-02
Description:
HDD trouble when the mirroring kit is installed
Causes:
When installing the mirroring kit, the HDD of the machine or the HDD of the mirroring kit breaks down or connection fails. • Defective installation of the mirroring kit • Breakdown of the HDD of the mirroring kit • Defective connection between the HDD and the mirroring kit harness • MFPC PWB trouble
Remedy:
• Use SIM62-20 to check the trouble. • Check installation of the mirroring kit (connector and harness), and replace if necessary. • Replace the broken HDD. • Replace the mirroring kit. • Replace the MFPC PWB.
Code: E7-03
Description:
HDD trouble (When the mirroring kit is not installed)
Causes:
Connector, harness connection trouble in the MFPC PWB and HDD. HDD (error file management area) data abnormality (FAT breakage). MFPC PWB trouble. Cause (When the mirroring kit is not installed) RAID PWB trouble. A HDD which has been used for mirroring is installed. Both HDD's go into trouble under the use environment of mirroring.
Remedy:
Check connection of the connector and the harness of the MFPC PWB and HDD. Use SIM62-2, 3 to check read/write operations of the HDD. Replace the HDD. Check or replace the MFPC PWB. (When the mirroring kit is installed) Check the RAID PWB, and replace if necessary. Replace the HDD. (For details, refer to the HDD and RAID PWB replacement procedures under mirroring environment.)
Code: E7-03
Description:
HDD trouble (When the mirroring kit is installed)
Causes:
Connector, harness connection trouble in the MFPC PWB and HDD. HDD (error file management area) data abnormality (FAT breakage). MFPC PWB trouble. (When the mirroring kit is installed) RAID PWB trouble. A HDD which has been used for mirroring is installed. Both HDD's go into trouble under the use environment of mirroring.
Remedy:
Check connection of the connector and the harness of the MFPC PWB and HDD. Use SIM62-2, 3 to check read/write operations of the HDD. Replace the HDD. Check or replace the MFPC PWB. (When the mirroring kit is installed) Check the RAID PWB, and replace if necessary. Replace the HDD. (For details, refer to the HDD and RAID PWB replacement procedures under mirroring environment.)
Code: E7-04
Description:
HDD-ASIC error
Causes:
HDD-ASIC trouble. (MFPC PWB trouble.) An error occurs in the HDD-ASIC self test when booting.
Remedy:
Check or replace the MFPC PWB.
Code: E7-07
Description:
SD card error
Causes:
SD card trouble or contact error MFPC PWB trouble.
Remedy:
Replace the SD card. Check the SD card socket. Replace the MFPC PWB.
Code: E7-10
Description:
Shading error (Black correction)
Causes:
Abnormality in the CCD black scan level when the scanner lamp is turned OFF. Improper installation of the harness to the CCD unit. CCD unit abnormality. SCU PWB abnormality.
Remedy:
Check connection of the harness to the CCD unit. Check the CCD unit. Check the SCU PWB.
Code: E7-11
Description:
Shading error (White correction)
Causes:
Abnormality in the CCD white reference plate scan level when the scanner lamp is turned ON. Improper installation of the harness to the CCD unit. Dirt on the mirror, lens, and the reference white plate. Scanner lamp lighting trouble. Scanner lamp drive PWB trouble CCD unit abnormality. SCU PWB abnormality.
Remedy:
Check connection of the harness to the CCD unit. Check connection of the harness to the scanner lamp unit. Check or replace the scanner lamp. Check or replace the scanner lamp drive PWB. Clean or replace the mirror, the lens, and the reference white board. Check or replace the CCD unit. Check or replace the SCU PWB.
Code: E7-14
Description:
CCD-ASIC error
Causes:
SCU PWB trouble.
Remedy:
Check the SCU PWB. Replace the SCU PWB.
Code: E7-20
Description:
LSU laser detection and deterioration error (K)
Causes:
Laser optical axis misalignment Reduced laser power, lighting error, laser diode trouble. LSU harness, connector trouble LSU trouble
Remedy:
Use SIM61-1 to check the operation of the LSU. Check or replace the LSU control PWB. Check connection of the LSU harness. Replace the LSU.
Code: E7-21
Description:
LSU laser deterioration error
Causes:
Reduced laser power, lighting error, laser diode trouble. LSU harness, connector trouble LSU trouble
Remedy:
Use SIM61-1 to check the operation of the LSU. Check or replace the LSU control PWB. Check connection of the LSU harness. Replace the LSU.
Code: E7-24
Description:
LSU LD driver trouble
Causes:
Disconnection or improper connection of the harness and the connector between the LD PWB and the LSU control PWB. LD PWB/LSU control PWB trouble.
Remedy:
Use SIM61-01 to check the operations of the LSU. Check the harness and the connector between the LD PWB and the LSU control PWB. Replace the LD PWB/LSU control PWB.
Code: E7-28
Description:
LSU - PCU connection error
Causes:
Communication error between the CPU in the PCU PWB and the LSU control ASIC. Improper connection of the communication connector between the PCU PWB and the LSU control PWB (interface PWB). Harness trouble between the PCU PWB and the LSU control PWB (interface PWB) PCU PWB trouble. LSU control PWB trouble. LSU trouble.
Remedy:
Check connection of the connector and the harness between the PCU PWB and the LSU control PWB. Replace the LSU control PWB. Replace the PCU PWB. Replace the LSU.
Code: E7-29
Description:
LSU ASIC frequency error
Causes:
Oscillation abnormality of the external oscillator used in the LSU ASIC. LSU ASIC abnormality on the LSU control PWB.
Remedy:
Replace the LSU control PWB.
Code: E7-35
Description:
Communication trouble with the CIS-ASIC
Causes:
Connector/harness trouble between the PCU PWB and the PEDCis PWB. PEDCis PWB trouble, PCU PWB trouble. PS unit drawer connector insertion trouble.
Remedy:
Check the harness between the PCU PWB and the PEDCis PWB. Check the PEDCis PWB, and the PCU PWB. If the trouble is not canceled, replace the PEDCis PWB and the PCU PWB.
Code: E7-36
Description:
CIS-ASIC black level detection abnormality
Causes:
The CIS unit is not installed properly. Harness trouble between the CIS unit and the PEDCis PWB. CIS unit trouble, PEDCis PWB trouble. Dirt on the reference black plate.
Remedy:
Check the installing state of the CIS unit Check the harness between the CIS unit and the PEDCis PWB. Clean the reference black plate. If the trouble is not canceled, replace the CIS unit and the PEDCis PWB.
Code: E7-37
Description:
CIS-ASIC white level detection abnormality
Causes:
The CIS unit is not installed properly. Harness trouble between the CIS unit and the PEDCis PWB. CIS unit trouble, PEDCis PWB trouble. Dirt on the reference white plate.
Remedy:
Check the installing state of the CIS unit Check the harness between the CIS unit and the PEDCis PWB. Clean the reference white plate. If the trouble is not canceled, replace the CIS unit and the PEDCis PWB.
Code: E7-42
Description:
Image data trouble (Scanner expansion PWB (ACRE) ASIC)
Causes:
An image data error occurs. An image data send error occurs. Scanner expansion PWB (ACRE) connection trouble. Scanner expansion PWB (ACRE) trouble. MFPC PWB trouble.
Remedy:
Check connection of the scanner expansion PWB (ACRE). Check the scanner expansion PWB (ACRE), and replace if necessary. Check the MFPC PWB, and replace if necessary.
Code: E7-46
Description:
Image data decode error (Scanner expansion PWB (ACRE) ASIC)
Causes:
A decode error occurs while high compression PDF images are made. (garbled data) Scanner expansion PWB (ACRE) connection trouble. Scanner expansion PWB (ACRE) trouble. MFPC PWB trouble.
Remedy:
Check connection of the scanner expansion PWB (ACRE). Check the scanner expansion PWB (ACRE), and replace if necessary. Check the MFPC PWB, and replace if necessary.
Code: E7-48
Description:
Scanner expansion PWB (ACRE) ASIC memory error
Causes:
Scanner expansion PWB (ACRE) DIMM trouble, memory slot trouble. Scanner expansion PWB (ACRE) DIMM insertion trouble. Scanner expansion PWB (ACRE) connection trouble. Scanner expansion PWB (ACRE) trouble. MFPC PWB trouble.
Remedy:
Check insertion of the scanner expansion PWB (ACRE) DIMM memory. Check the scanner expansion PWB (ACRE) DIMM memory, and replace if necessary. Check connection of the scanner expansion PWB (ACRE). Check the scanner expansion PWB (ACRE), and replace if necessary. Check the MFPC PWB, and replace if necessary.
Code: E7-49
Description:
Water Mark data error
Causes:
Watermark data trouble. HDD trouble.
Remedy:
Use SIM49-5 to upload the watermark data. Replace the HDD.
Code: E7-50
Description:
Engine connection trouble
Causes:
A PWB/firmware/LSU which is not compatible with the machine specifications is detected. PCU PWB trouble LSU trouble
Remedy:
Check the kind and the version of the firmware. Check or replace the LSU. Check or replace the PCU PWB.
Code: E7-55
Description:
PWB information sum error (engine detection)
Causes:
EEPROM device trouble. EEPROM device contact trouble. Device access error due to noises.
Remedy:
Replace the PWB.
Code: E7-58
Description:
PWB information sum error (engine other detection)
Causes:
LSU connection failure PCU PWB trouble. LSU trouble.
Remedy:
Replace the LSU control PWB. Replace the PCU PWB. Replace the LSU.
Code: E7-60
Description:
Combination error between PWB and firmware (MFPC PWB detection)
Causes:
A PWB/firmware which is not compatible with the machine specifications is detected in the MFPC PWB. MFPC PWB trouble.
Remedy:
Check the kind and the version of the firmware. Check or replace the MFPC PWB.
Code: E7-61
Description:
Combination error between the MFPC PWB and the PCU PWB (MFPC PWB detection)
Causes:
Combination error between the MFPC PWB and the PCU PWB. MFPC PWB trouble. PCU PWB trouble.
Remedy:
Check the combination between the MFPC PWB and the PCU PWB. Replace the MFPC PWB. Replace the PCU PWB.
Code: E7-62
Description:
Controller connection trouble (scanner)
Causes:
Combination error between the controller PWB and the engine.
Remedy:
Check the controller PWB. Check combination between the controller PWB and the scanner.
Code: E7-65
Description:
MFP EEPROM sum check error
Causes:
EEPROM device trouble. EEPROM device contact trouble. Device access error due to noises.
Remedy:
Replace the PWB.
Code: E7-70
Description:
Scanner connection trouble
Causes:
The PWB / firmware which is not supported by the machine specifications is connected. SCU PWB trouble. DSPF PWB trouble.
Remedy:
Check the firmware kind and the version. Check the SCU PWB. Check the DSPF PWB.
Code: E7-71
Description:
DSPF connection trouble
Causes:
PWB / firmware which does not support the machine specifications is connected.
Remedy:
Firmware kind / Version check.
Code: E7-80
Description:
MFP - SCU PWB communication error
Causes:
SCU PWB - MFPC PWB connection trouble. SCU PWB trouble. MFPC PWB trouble.
Remedy:
Check connection of the SCU PWB and the MFPC PWB. Check the ground. Replace the SCU PWB. Replace the MFPC PWB.
Code: E7-89
Description:
Communication error between MFPC PWB CPU and energy-saving NIC controller
Causes:
MFPC PWB trouble.
Remedy:
Replace the MFPC PWB.
Code: E7-90
Description:
MFP - PCU PWB communication error
Causes:
PCU PWB - MFPC PWB connection trouble. PCU PWB trouble. MFPC PWB trouble.
Remedy:
Check connection of the PCU PWB and the MFPC PWB. Check the ground. Replace the PCU PWB. Replace the MFPC PWB.
Code: E7-91
Description:
FAX reception image data error
Causes:
Image data process abnormality HDD trouble SD card trouble or contact error Image compression data corruption MFPC PWB trouble DIMM memory trouble or contact error FAX control PWB trouble
Remedy:
Use SIM60-01 to check the read/write operations of the memory. Replace the HDD. Replace or check installation of the SD card. Replace the MFPC PWB. Replace or check installation of the DIMM memory. Replace the FAX control PWB.
Code: E7-92
Description:
Copy image data error
Causes:
Image data process abnormality HDD trouble Image compression data corruption MFPC PWB trouble DIMM memory trouble or contact error
Remedy:
Use SIM60-01 to check the read/write operations of the memory. Replace the HDD. Replace the MFPC PWB. Replace or check installation of the DIMM memory.
Code: E7-93
Description:
Copy, image send, filing, print image data process error
Causes:
Image data process abnormality HDD trouble Image compression data corruption MFPC PWB trouble DIMM memory trouble or contact error
Remedy:
Use SIM60-01 to check the read/write operations of the memory. Replace the HDD. Replace the MFPC PWB. Replace or check installation of the DIMM memory.
Code: E7-94
Description:
Image file data process error (when importing file data)
Causes:
Image data process abnormality HDD trouble Image compression data corruption MFPC PWB trouble DIMM memory trouble or contact error
Remedy:
Use SIM60-01 to check the read/write operations of the memory. Replace the HDD. Replace the MFPC PWB. Replace or check installation of the DIMM memory.
Code: E7-95
Description:
Printer PWB DIMM memory check error
Causes:
Memory data corruption occurs MFPC PWB trouble DIMM memory trouble or contact error
Remedy:
Use SIM60-01 to check the read/write operations of the memory. Replace the MFPC PWB. DIMM memory socket check Replace the DIMM memory.
Code: E7-96
Description:
MFPC PWB DIMM memory check error
Causes:
Memory data corruption occurs MFPC PWB trouble DIMM memory trouble or contact error
Remedy:
Use SIM60-01 to check the read/write operations of the memory. Replace the MFPC PWB. DIMM memory socket check Replace the DIMM memory.
Code: E7-A0
Description:
LSU EEPROM/LD driver read/write error (K)
Causes:
EEPROM/LD driver trouble. EEPROM/LD driver access circuit trouble.
Remedy:
Check connection of the connector and the harness of the LD PWB and the PCU PWB. Replace the PCU PWB. If the above remedies cannot delete the trouble, replace the LSU.
Code: E7-A5
Description:
Installation error of HDD which was used in the mirroring kit
Causes:
A HDD which was used in the mirroring kit is installed to the MFP without the mirroring kit.
Remedy:
Replace the HDD with one which has not been used in the mirroring kit.
Code: EE-EC
Description:
Automatic toner density adjustment error
Causes:
Toner density sensor trouble. Developing unit trouble. PCU PWB trouble.
Remedy:
Replace the toner density sensor. Replace the developing unit. Replace the PCU PWB.
Code: EE-EL
Description:
Automatic toner density adjustment error (Over toner)
Causes:
Toner density sensor trouble. Developing unit trouble. PCU PWB trouble
Remedy:
Replace the toner density sensor. Replace the developing unit. Replace the PCU PWB.
Code: EE-EU
Description:
Automatic toner density adjustment error (Under toner)
Causes:
Toner density sensor trouble. Developing unit trouble. PCU PWB trouble.
Remedy:
Replace the toner density sensor. Replace the developing unit. Replace the PCU PWB.
Code: F0-03
Description:
Finisher paper exit roller lift motor section abnormality (FNM110)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, hp sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the paper exit roller lift motor. Check connection from the control PWB to the motor and the sensor. Replace the control PWB, the motor, and the sensor part.
Code: F0-08
Description:
Finisher stapler shift motor section abnormality (FNM107)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, hp sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the stapler shift motor. Check connection from the control PWB to the motor and the sensor. Replace the control PWB, the motor, and the sensor part.
Code: F0-10
Description:
Finisher staple motor section abnormality (FNM115)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, hp sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the staple motor. Check connection from the control PWB to the motor and the sensor. Replace the control PWB, the motor, and the sensor part.
Code: F0-11
Description:
Finisher bundle exit motor section abnormality (FNM116)
Causes:
Motor lock, motor harness short/open, control PWB trouble, hp sensor breakdown, disconnection of harness or connector.
Remedy:
Use SIM3-3 to check the operation of the gripper arm motor (FNM116). Check connection from the control PWB to the motor. Replace the control PWB and the sensor part.
Code: F0-14
Description:
Finisher paper rear edge falling motor section abnormality (FNM113)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, hp sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the rear edge falling motor. Check connection from the control PWB to the motor and the sensor. Replace the control PWB, the motor, and the sensor part
Code: F0-15
Description:
Finisher tray lift motor section abnormality (FNM106)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, area sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the upper tray lift motor and the lower tray lift motor. Check connection from the control PWB to the motor and the sensor. Replace the control PWB, and motor, and the sensor part.
Code: F0-18
Description:
Finisher rear edge hold motor section abnormality (FNM118)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, hp sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the paper hold motor. Check connection from the control PWB to the motor and the sensor. Replace the control PWB, the motor, and the sensor part.
Code: F0-19
Description:
Finisher paper alignment motor F section abnormality (FNM108)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, hp sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the paper alignment motor F. Check connection from the control PWB to the motor and the sensor. Replace the control PWB, the motor, and the sensor part.
Code: F0-20
Description:
Finisher paper alignment motor R section abnormality (FNM109)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, hp sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the paper alignment motor R. Check connection from the control PWB to the motor and the sensor. Replace the control PWB, the motor, and the sensor part.
Code: F0-23
Description:
Shutter trouble (FNCL102)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, hp sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the shutter clutch. Check connection from the control PWB to the clutch and the sensor. Replace the control PWB, the clutch, and the sensor part.
Code: F0-25
Description:
Finisher paper transport roller lift motor section abnormality (FNM119)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, hp sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the paper transport roller lift motor. Check connection from the control PWB to the motor and the sensor. Replace the control PWB, the motor, and the sensor part.
Description:
PCU PWB ROM error
Causes:
The firmware version-up is not completed properly by interruption of the power during the version-up operation, etc. PCU PWB trouble.
Remedy:
Use SIM49-1 to perform the firmware version-up procedure again. Replace the PCU PWB.
Code: A0-02
Description:
SCU PWB ROM error
Causes:
The firmware version-up is not completed properly by interruption of the power during the version-up operation, etc. SCU PWB trouble.
Remedy:
Use SIM49-1 to perform the firmware version-up procedure again. Replace the SCU PWB.
Code: A0-04
Description:
Scanner expansion PWB (ACU) (ACRE) ROM error
Causes:
Scanner expansion PWB (ACU) (ACRE) ROM data error. An error occurs during firmware upgrading for some reasons.
Remedy:
Perform firmware upgrading again.
Code: A0-05
Description:
Scanner expansion PWB (ACU) (ACRE) firmware error
Causes:
Improper firmware A firmware of a different model is installed. A ROM of a different model is installed.
Remedy:
Replace the ROM with a proper one. Write the proper firmware. (Upgrade to the proper firmware.)
Code: A0-10
Description:
MFPC PWB ROM error
Causes:
CTL and the image ROM firmware combination error
Remedy:
Check the firmware combination of CTL and the image ROM.
Code: A0-11
Description:
Firmware version inconsistency (MFP - PCU)
Causes:
Firmware combination error between the MFP and the PCU.
Remedy:
Install the firmware in the all-firmware version-up mode.
Code: A0-14
Description:
Inconsistency between the MFP and the CPU firmware version
Causes:
Combination error between the MFP and the CPU UI firmware version.
Remedy:
Install the firmware in the all-firmware version-up mode.
Code: A0-15
Description:
Incompatible DSK BOOT and program firmware
Causes:
Installation of the normal firmware was performed with a security kit enable.
Remedy:
Stop installation of the normal firmware.
Code: A0-16
Description:
Data error of the energy-saving NIC controller firmware in the SD card
Causes:
SD card trouble. MFPC PWB trouble.
Remedy:
Reinstall the firmware. Replace the SD card. Replace the MFPC PWB.
Code: A0-17
Description:
Inconsistency between the UI data and the CPU firmware version
Causes:
Combination error between the UI contents data and the CPU UI firmware version.
Remedy:
Install the firmware in the all-firmware version-up mode.
Code: A0-20
Description:
Conflict firmware and EEPROM data version (MFP)
Causes:
Inconsistency between the MFP firmware version and the EEPROM data version.
Remedy:
Check the combination of the firmware.
Code: A0-21
Description:
Conflict firmware and EEPROM data version (PCU)
Causes:
Inconsistency between the PCU firmware version and the EEPROM data version.
Remedy:
Check the combination of the firmware.
Code: A0-22
Description:
Conflict firmware and EEPROM data version (SCU)
Causes:
Inconsistency between the SCU firmware version and the EEPROM data version.
Remedy:
Check the combination of the firmware.
Code: C1-01
Description:
Charger cleaner trouble (K)
Causes:
The main charger unit (K) is not installed properly. There is an abnormality in the main charger unit (K). Connector connection trouble of the drum unit (K) hp sensor, the discharge lamp, or the after-transfer discharge lamp. Harness disconnection of the drum unit (K) hp sensor, the discharge lamp, or the after-transfer discharge lamp. hp sensor dirt. Charger cleaner motor (K) trouble. PCU PWB connector connection trouble/PWB trouble.
Remedy:
Use SIM6-4 to check the operation of the charger cleaner. Check disconnection of the main charger unit./ Replace. Check for disconnection of the connector of the drum unit (K) hp sensor, the discharge lamp, and the aftertransfer discharge lamp. Check the harness of the drum unit (K) hp sensor, the discharge lamp, and the after-transfer discharge lamp. (Since the earth wire is common to them, check the three positions.) Clean the hp sensor. Check disconnection of the PCU PWB connector./ Replace PWB. Replace the charger cleaner motor (K).
Code: C1-10
Description:
Main charger trouble (Monochrome)
Causes:
The main charger unit (K) is not installed properly. There is an abnormality in the main charger unit (K). Disconnection of the high voltage PWB connector. Breakage of the high voltage harness. High voltage PWB trouble. PCU PWB trouble.
Remedy:
Check the output of the main charger with SIM8-2. Check disconnection of the main charger./Replace. Check disconnection of the high voltage PWB connector./Replace. Replace the high voltage PWB. Replace the PCU PWB.
Code: C4-20
Description:
Transfer high voltage output trouble
Causes:
Transfer unit abnormality. Transfer unit insertion trouble. TC output harness disconnection, breakage. Transfer unit separation operation trouble. OPC drum abnormality (Does not rotate.) High voltage PWB trouble. PCU PWB trouble. PCU PWB - high voltage PWB harness disconnection, breakage.
Remedy:
Replace the transfer unit. Reinsert the transfer unit. Check or replace the TC output harness. Replace the high voltage PWB. Replace the PCU PWB. Check the harness between the PCU PWB and the high voltage PWB, and replace as needed.
Code: E6-10
Description:
DSPF shading error (Black correction)
Causes:
Installation error of the CCD unit harness. CCD unit trouble. DSPF PWB trouble.
Remedy:
Check the installing state of the harness to the CCD unit. Check the CCD unit. Check the DSPF PWB.
Code: E6-11
Description:
DSPF shading error (White correction)
Causes:
Installation error of the CCD unit harness. Copy lamp lighting trouble. Dirt on the mirror, the lens, or the reference white plate. CCD unit trouble. DSPF PWB trouble. Shading SIM not executed / Shading ROM abnormality.
Remedy:
Check the installing state of the harness the CCD unit. Check the installing state of the harness to the copy lamp unit. Clean the mirror, the lens, or the reference white plate. Check the CCD unit. Check the DSPF PWB.
Code: E6-14
Description:
DSPF CCD-ASIC error
Causes:
DSPF PWB trouble.
Remedy:
Check the DSPF PWB.
Code: E7-01
Description:
MFP image data error
Causes:
Image data transfer error in the MFPC PWB. MFPC PWB trouble.
Remedy:
Check connection of the connector and the harness of the MFPC PWB. Check or replace the MFPC PWB.
Code: E7-02
Description:
HDD trouble when the mirroring kit is installed
Causes:
When installing the mirroring kit, the HDD of the machine or the HDD of the mirroring kit breaks down or connection fails. • Defective installation of the mirroring kit • Breakdown of the HDD of the mirroring kit • Defective connection between the HDD and the mirroring kit harness • MFPC PWB trouble
Remedy:
• Use SIM62-20 to check the trouble. • Check installation of the mirroring kit (connector and harness), and replace if necessary. • Replace the broken HDD. • Replace the mirroring kit. • Replace the MFPC PWB.
Code: E7-03
Description:
HDD trouble (When the mirroring kit is not installed)
Causes:
Connector, harness connection trouble in the MFPC PWB and HDD. HDD (error file management area) data abnormality (FAT breakage). MFPC PWB trouble. Cause (When the mirroring kit is not installed) RAID PWB trouble. A HDD which has been used for mirroring is installed. Both HDD's go into trouble under the use environment of mirroring.
Remedy:
Check connection of the connector and the harness of the MFPC PWB and HDD. Use SIM62-2, 3 to check read/write operations of the HDD. Replace the HDD. Check or replace the MFPC PWB. (When the mirroring kit is installed) Check the RAID PWB, and replace if necessary. Replace the HDD. (For details, refer to the HDD and RAID PWB replacement procedures under mirroring environment.)
Code: E7-03
Description:
HDD trouble (When the mirroring kit is installed)
Causes:
Connector, harness connection trouble in the MFPC PWB and HDD. HDD (error file management area) data abnormality (FAT breakage). MFPC PWB trouble. (When the mirroring kit is installed) RAID PWB trouble. A HDD which has been used for mirroring is installed. Both HDD's go into trouble under the use environment of mirroring.
Remedy:
Check connection of the connector and the harness of the MFPC PWB and HDD. Use SIM62-2, 3 to check read/write operations of the HDD. Replace the HDD. Check or replace the MFPC PWB. (When the mirroring kit is installed) Check the RAID PWB, and replace if necessary. Replace the HDD. (For details, refer to the HDD and RAID PWB replacement procedures under mirroring environment.)
Code: E7-04
Description:
HDD-ASIC error
Causes:
HDD-ASIC trouble. (MFPC PWB trouble.) An error occurs in the HDD-ASIC self test when booting.
Remedy:
Check or replace the MFPC PWB.
Code: E7-07
Description:
SD card error
Causes:
SD card trouble or contact error MFPC PWB trouble.
Remedy:
Replace the SD card. Check the SD card socket. Replace the MFPC PWB.
Code: E7-10
Description:
Shading error (Black correction)
Causes:
Abnormality in the CCD black scan level when the scanner lamp is turned OFF. Improper installation of the harness to the CCD unit. CCD unit abnormality. SCU PWB abnormality.
Remedy:
Check connection of the harness to the CCD unit. Check the CCD unit. Check the SCU PWB.
Code: E7-11
Description:
Shading error (White correction)
Causes:
Abnormality in the CCD white reference plate scan level when the scanner lamp is turned ON. Improper installation of the harness to the CCD unit. Dirt on the mirror, lens, and the reference white plate. Scanner lamp lighting trouble. Scanner lamp drive PWB trouble CCD unit abnormality. SCU PWB abnormality.
Remedy:
Check connection of the harness to the CCD unit. Check connection of the harness to the scanner lamp unit. Check or replace the scanner lamp. Check or replace the scanner lamp drive PWB. Clean or replace the mirror, the lens, and the reference white board. Check or replace the CCD unit. Check or replace the SCU PWB.
Code: E7-14
Description:
CCD-ASIC error
Causes:
SCU PWB trouble.
Remedy:
Check the SCU PWB. Replace the SCU PWB.
Code: E7-20
Description:
LSU laser detection and deterioration error (K)
Causes:
Laser optical axis misalignment Reduced laser power, lighting error, laser diode trouble. LSU harness, connector trouble LSU trouble
Remedy:
Use SIM61-1 to check the operation of the LSU. Check or replace the LSU control PWB. Check connection of the LSU harness. Replace the LSU.
Code: E7-21
Description:
LSU laser deterioration error
Causes:
Reduced laser power, lighting error, laser diode trouble. LSU harness, connector trouble LSU trouble
Remedy:
Use SIM61-1 to check the operation of the LSU. Check or replace the LSU control PWB. Check connection of the LSU harness. Replace the LSU.
Code: E7-24
Description:
LSU LD driver trouble
Causes:
Disconnection or improper connection of the harness and the connector between the LD PWB and the LSU control PWB. LD PWB/LSU control PWB trouble.
Remedy:
Use SIM61-01 to check the operations of the LSU. Check the harness and the connector between the LD PWB and the LSU control PWB. Replace the LD PWB/LSU control PWB.
Code: E7-28
Description:
LSU - PCU connection error
Causes:
Communication error between the CPU in the PCU PWB and the LSU control ASIC. Improper connection of the communication connector between the PCU PWB and the LSU control PWB (interface PWB). Harness trouble between the PCU PWB and the LSU control PWB (interface PWB) PCU PWB trouble. LSU control PWB trouble. LSU trouble.
Remedy:
Check connection of the connector and the harness between the PCU PWB and the LSU control PWB. Replace the LSU control PWB. Replace the PCU PWB. Replace the LSU.
Code: E7-29
Description:
LSU ASIC frequency error
Causes:
Oscillation abnormality of the external oscillator used in the LSU ASIC. LSU ASIC abnormality on the LSU control PWB.
Remedy:
Replace the LSU control PWB.
Code: E7-35
Description:
Communication trouble with the CIS-ASIC
Causes:
Connector/harness trouble between the PCU PWB and the PEDCis PWB. PEDCis PWB trouble, PCU PWB trouble. PS unit drawer connector insertion trouble.
Remedy:
Check the harness between the PCU PWB and the PEDCis PWB. Check the PEDCis PWB, and the PCU PWB. If the trouble is not canceled, replace the PEDCis PWB and the PCU PWB.
Code: E7-36
Description:
CIS-ASIC black level detection abnormality
Causes:
The CIS unit is not installed properly. Harness trouble between the CIS unit and the PEDCis PWB. CIS unit trouble, PEDCis PWB trouble. Dirt on the reference black plate.
Remedy:
Check the installing state of the CIS unit Check the harness between the CIS unit and the PEDCis PWB. Clean the reference black plate. If the trouble is not canceled, replace the CIS unit and the PEDCis PWB.
Code: E7-37
Description:
CIS-ASIC white level detection abnormality
Causes:
The CIS unit is not installed properly. Harness trouble between the CIS unit and the PEDCis PWB. CIS unit trouble, PEDCis PWB trouble. Dirt on the reference white plate.
Remedy:
Check the installing state of the CIS unit Check the harness between the CIS unit and the PEDCis PWB. Clean the reference white plate. If the trouble is not canceled, replace the CIS unit and the PEDCis PWB.
Code: E7-42
Description:
Image data trouble (Scanner expansion PWB (ACRE) ASIC)
Causes:
An image data error occurs. An image data send error occurs. Scanner expansion PWB (ACRE) connection trouble. Scanner expansion PWB (ACRE) trouble. MFPC PWB trouble.
Remedy:
Check connection of the scanner expansion PWB (ACRE). Check the scanner expansion PWB (ACRE), and replace if necessary. Check the MFPC PWB, and replace if necessary.
Code: E7-46
Description:
Image data decode error (Scanner expansion PWB (ACRE) ASIC)
Causes:
A decode error occurs while high compression PDF images are made. (garbled data) Scanner expansion PWB (ACRE) connection trouble. Scanner expansion PWB (ACRE) trouble. MFPC PWB trouble.
Remedy:
Check connection of the scanner expansion PWB (ACRE). Check the scanner expansion PWB (ACRE), and replace if necessary. Check the MFPC PWB, and replace if necessary.
Code: E7-48
Description:
Scanner expansion PWB (ACRE) ASIC memory error
Causes:
Scanner expansion PWB (ACRE) DIMM trouble, memory slot trouble. Scanner expansion PWB (ACRE) DIMM insertion trouble. Scanner expansion PWB (ACRE) connection trouble. Scanner expansion PWB (ACRE) trouble. MFPC PWB trouble.
Remedy:
Check insertion of the scanner expansion PWB (ACRE) DIMM memory. Check the scanner expansion PWB (ACRE) DIMM memory, and replace if necessary. Check connection of the scanner expansion PWB (ACRE). Check the scanner expansion PWB (ACRE), and replace if necessary. Check the MFPC PWB, and replace if necessary.
Code: E7-49
Description:
Water Mark data error
Causes:
Watermark data trouble. HDD trouble.
Remedy:
Use SIM49-5 to upload the watermark data. Replace the HDD.
Code: E7-50
Description:
Engine connection trouble
Causes:
A PWB/firmware/LSU which is not compatible with the machine specifications is detected. PCU PWB trouble LSU trouble
Remedy:
Check the kind and the version of the firmware. Check or replace the LSU. Check or replace the PCU PWB.
Code: E7-55
Description:
PWB information sum error (engine detection)
Causes:
EEPROM device trouble. EEPROM device contact trouble. Device access error due to noises.
Remedy:
Replace the PWB.
Code: E7-58
Description:
PWB information sum error (engine other detection)
Causes:
LSU connection failure PCU PWB trouble. LSU trouble.
Remedy:
Replace the LSU control PWB. Replace the PCU PWB. Replace the LSU.
Code: E7-60
Description:
Combination error between PWB and firmware (MFPC PWB detection)
Causes:
A PWB/firmware which is not compatible with the machine specifications is detected in the MFPC PWB. MFPC PWB trouble.
Remedy:
Check the kind and the version of the firmware. Check or replace the MFPC PWB.
Code: E7-61
Description:
Combination error between the MFPC PWB and the PCU PWB (MFPC PWB detection)
Causes:
Combination error between the MFPC PWB and the PCU PWB. MFPC PWB trouble. PCU PWB trouble.
Remedy:
Check the combination between the MFPC PWB and the PCU PWB. Replace the MFPC PWB. Replace the PCU PWB.
Code: E7-62
Description:
Controller connection trouble (scanner)
Causes:
Combination error between the controller PWB and the engine.
Remedy:
Check the controller PWB. Check combination between the controller PWB and the scanner.
Code: E7-65
Description:
MFP EEPROM sum check error
Causes:
EEPROM device trouble. EEPROM device contact trouble. Device access error due to noises.
Remedy:
Replace the PWB.
Code: E7-70
Description:
Scanner connection trouble
Causes:
The PWB / firmware which is not supported by the machine specifications is connected. SCU PWB trouble. DSPF PWB trouble.
Remedy:
Check the firmware kind and the version. Check the SCU PWB. Check the DSPF PWB.
Code: E7-71
Description:
DSPF connection trouble
Causes:
PWB / firmware which does not support the machine specifications is connected.
Remedy:
Firmware kind / Version check.
Code: E7-80
Description:
MFP - SCU PWB communication error
Causes:
SCU PWB - MFPC PWB connection trouble. SCU PWB trouble. MFPC PWB trouble.
Remedy:
Check connection of the SCU PWB and the MFPC PWB. Check the ground. Replace the SCU PWB. Replace the MFPC PWB.
Code: E7-89
Description:
Communication error between MFPC PWB CPU and energy-saving NIC controller
Causes:
MFPC PWB trouble.
Remedy:
Replace the MFPC PWB.
Code: E7-90
Description:
MFP - PCU PWB communication error
Causes:
PCU PWB - MFPC PWB connection trouble. PCU PWB trouble. MFPC PWB trouble.
Remedy:
Check connection of the PCU PWB and the MFPC PWB. Check the ground. Replace the PCU PWB. Replace the MFPC PWB.
Code: E7-91
Description:
FAX reception image data error
Causes:
Image data process abnormality HDD trouble SD card trouble or contact error Image compression data corruption MFPC PWB trouble DIMM memory trouble or contact error FAX control PWB trouble
Remedy:
Use SIM60-01 to check the read/write operations of the memory. Replace the HDD. Replace or check installation of the SD card. Replace the MFPC PWB. Replace or check installation of the DIMM memory. Replace the FAX control PWB.
Code: E7-92
Description:
Copy image data error
Causes:
Image data process abnormality HDD trouble Image compression data corruption MFPC PWB trouble DIMM memory trouble or contact error
Remedy:
Use SIM60-01 to check the read/write operations of the memory. Replace the HDD. Replace the MFPC PWB. Replace or check installation of the DIMM memory.
Code: E7-93
Description:
Copy, image send, filing, print image data process error
Causes:
Image data process abnormality HDD trouble Image compression data corruption MFPC PWB trouble DIMM memory trouble or contact error
Remedy:
Use SIM60-01 to check the read/write operations of the memory. Replace the HDD. Replace the MFPC PWB. Replace or check installation of the DIMM memory.
Code: E7-94
Description:
Image file data process error (when importing file data)
Causes:
Image data process abnormality HDD trouble Image compression data corruption MFPC PWB trouble DIMM memory trouble or contact error
Remedy:
Use SIM60-01 to check the read/write operations of the memory. Replace the HDD. Replace the MFPC PWB. Replace or check installation of the DIMM memory.
Code: E7-95
Description:
Printer PWB DIMM memory check error
Causes:
Memory data corruption occurs MFPC PWB trouble DIMM memory trouble or contact error
Remedy:
Use SIM60-01 to check the read/write operations of the memory. Replace the MFPC PWB. DIMM memory socket check Replace the DIMM memory.
Code: E7-96
Description:
MFPC PWB DIMM memory check error
Causes:
Memory data corruption occurs MFPC PWB trouble DIMM memory trouble or contact error
Remedy:
Use SIM60-01 to check the read/write operations of the memory. Replace the MFPC PWB. DIMM memory socket check Replace the DIMM memory.
Code: E7-A0
Description:
LSU EEPROM/LD driver read/write error (K)
Causes:
EEPROM/LD driver trouble. EEPROM/LD driver access circuit trouble.
Remedy:
Check connection of the connector and the harness of the LD PWB and the PCU PWB. Replace the PCU PWB. If the above remedies cannot delete the trouble, replace the LSU.
Code: E7-A5
Description:
Installation error of HDD which was used in the mirroring kit
Causes:
A HDD which was used in the mirroring kit is installed to the MFP without the mirroring kit.
Remedy:
Replace the HDD with one which has not been used in the mirroring kit.
Code: EE-EC
Description:
Automatic toner density adjustment error
Causes:
Toner density sensor trouble. Developing unit trouble. PCU PWB trouble.
Remedy:
Replace the toner density sensor. Replace the developing unit. Replace the PCU PWB.
Code: EE-EL
Description:
Automatic toner density adjustment error (Over toner)
Causes:
Toner density sensor trouble. Developing unit trouble. PCU PWB trouble
Remedy:
Replace the toner density sensor. Replace the developing unit. Replace the PCU PWB.
Code: EE-EU
Description:
Automatic toner density adjustment error (Under toner)
Causes:
Toner density sensor trouble. Developing unit trouble. PCU PWB trouble.
Remedy:
Replace the toner density sensor. Replace the developing unit. Replace the PCU PWB.
Code: F0-03
Description:
Finisher paper exit roller lift motor section abnormality (FNM110)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, hp sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the paper exit roller lift motor. Check connection from the control PWB to the motor and the sensor. Replace the control PWB, the motor, and the sensor part.
Code: F0-08
Description:
Finisher stapler shift motor section abnormality (FNM107)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, hp sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the stapler shift motor. Check connection from the control PWB to the motor and the sensor. Replace the control PWB, the motor, and the sensor part.
Code: F0-10
Description:
Finisher staple motor section abnormality (FNM115)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, hp sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the staple motor. Check connection from the control PWB to the motor and the sensor. Replace the control PWB, the motor, and the sensor part.
Code: F0-11
Description:
Finisher bundle exit motor section abnormality (FNM116)
Causes:
Motor lock, motor harness short/open, control PWB trouble, hp sensor breakdown, disconnection of harness or connector.
Remedy:
Use SIM3-3 to check the operation of the gripper arm motor (FNM116). Check connection from the control PWB to the motor. Replace the control PWB and the sensor part.
Code: F0-14
Description:
Finisher paper rear edge falling motor section abnormality (FNM113)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, hp sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the rear edge falling motor. Check connection from the control PWB to the motor and the sensor. Replace the control PWB, the motor, and the sensor part
Code: F0-15
Description:
Finisher tray lift motor section abnormality (FNM106)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, area sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the upper tray lift motor and the lower tray lift motor. Check connection from the control PWB to the motor and the sensor. Replace the control PWB, and motor, and the sensor part.
Code: F0-18
Description:
Finisher rear edge hold motor section abnormality (FNM118)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, hp sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the paper hold motor. Check connection from the control PWB to the motor and the sensor. Replace the control PWB, the motor, and the sensor part.
Code: F0-19
Description:
Finisher paper alignment motor F section abnormality (FNM108)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, hp sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the paper alignment motor F. Check connection from the control PWB to the motor and the sensor. Replace the control PWB, the motor, and the sensor part.
Code: F0-20
Description:
Finisher paper alignment motor R section abnormality (FNM109)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, hp sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the paper alignment motor R. Check connection from the control PWB to the motor and the sensor. Replace the control PWB, the motor, and the sensor part.
Code: F0-23
Description:
Shutter trouble (FNCL102)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, hp sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the shutter clutch. Check connection from the control PWB to the clutch and the sensor. Replace the control PWB, the clutch, and the sensor part.
Code: F0-25
Description:
Finisher paper transport roller lift motor section abnormality (FNM119)
Causes:
Motor lock, control PWB trouble, disconnection of harness or connector, hp sensor breakdown.
Remedy:
Use SIM3-3 to check the operation of the paper transport roller lift motor. Check connection from the control PWB to the motor and the sensor. Replace the control PWB, the motor, and the sensor part.
熱門圖文