hp DesignJet 3000CP常見故障代碼描述,英文手冊
蘇州維修電話696l6769,維修點查詢,售后服務(wù),售后,技術(shù)服務(wù),客戶服務(wù),維修手冊,用戶手冊
Description:
Library Error.
Code: 010020
Description:
The Checksum read on the Flash SIMM is incorrect.
Code: 010021
Description:
The baseDRAM or theRAM SIMM tests failed.
Code: 010022
Description:
The SWATH RAM test failed.
Code: 010023
Description:
A fuse on the Main PCA has blown.
Code: 010024
Description:
Problem initializingthe encoder pulse generator.
Code: 010030
Description:
One of the two interconnect boards not detected.
Code: 010031
Description:
The Printhead Primitive Driver ASIC Test Failed.
Code: 010032
Description:
Fan Test Failed -Current not detected in one or bothfans. Error data (XX):
1 -Electronics Module fan not running. 2 -Service station fan not running. 3 -Bothfans not running. 10 -Electronics Module fan is short-circuited. 20 -Service Station fan is short-circuited. 30 -Bothfans are short-circuited. 12 -Service Station fan is not running and the Electronics Module fan is short-circuited. 21 -Electronics Module fan is not running and the Service Station fan is short-circuited.
Code: 010033
Description:
The DC Motor Driver ASIC Test Failed.
Code: 010034
Description:
One of the DC Motors has failed. Error data: 00010000 -Y-axis Motor Failed. 00020000 -X-axis Motor Failed. 00030000 -Both DC Motors Failed.
Code: 010035
Description:
One of the Stepper Motors has failed. Error data (oXABCDEF): If the value of each letter is o, then the component is OK. If the value of each letter is different from 0 then the component has failed. X -Electronics signal failed (ignore other values). A -Elevator Stepper Motor Failed. B -Refill Stepper Motor Failed. C -Primer Stepper Motor Failed. D -Service station (Z-axis) Stepper Motor Failed. E -Service station (X-axis) Stepper Motor Failed. F -Bail Stepper Motor Failed.
Code: 010036
Description:
ADC Test Failure in the Main PCA A short circuit in the Y/X-axis or ANY stepper motor. This short circuit is causing some of the fuses in the Electronics Module to burn. Error data: 00000800 -Problem with the Y-axis. 00001000 -Problem with the X-axis.
Code: 010037
Description:
ADC Test Failure in the Carriage PCA.
Code: 010038
Description:
A Printhead voltage could not be set -Main PCA Failure.
Code: 010039
Description:
A Printhead voltage could not be set -Carriage PCA Failure
Code: 010040
Description:
The Ambient Temperature measured is out of the normal range.
Code: 010042
Description:
The status of one of the opticalsensors is not stable when it should be. Error data (X): 0 -Problem with the Media Sensor. 1 -Problem with the Pinch-arm Sensor. 2 -Problem with the Refill Assembly Sensor. 3 -Problem with the Elevator Sensor. 4 -Problem with the Service Station Sensor. 5 -Problem with the Primer Sensor.
Code: 010043
Description:
Problem with theCarriageBoard.
Code: 010100
Description:
Error reading the EEROM.
Code: 010101
Description:
An action outside the EEROM limits has been performed.
Code: 010102
Description:
Physical EEROM write and/or write operations failed. The EEROM data that is written does not match the data that is read.
Code: 010110
Description:
The content of the permanent configuration area of theEEROM is not valid when theprinter is initialized in Service Mode.
Code: 010111
Description:
The content of the User configuration area of the EEROM is not valid when the printer is initialized.
Code: 010120
Description:
The content of the permanent configuration area of the EEROM is not valid when the printer is initialized in Normal Mode.
Code: 010121
Description:
One of the banks of the user area was corrupted while writing or reading in that area.
Code: 020000
Description:
Error in finding the Primer home position.
Code: 020001
Description:
Error in finding the Elevator home position.
Code: 020002
Description:
Error in finding the Refill Arm home position.
Code: 020003
Description:
Error in finding the Refill Stepper Motor home position.
Code: 020004
Description:
Error in finding the Service Station home position.
Code: 020005
Description:
Elevator has problem reaching a desired position.
Code: 020006
Description:
The refill position in the Y-axis is not calibrated.
Code: 020010
Description:
Problem with fine movement of the Y-axis motor.
Code: 020011
Description:
Error during initialization of the Y-axis.
Code: 040601
Description:
The MIO card does not support the MIO 6 protocol. Cards with version 5 or below can not be used with this plotter. Version 5.1 cards behave as expected but do not support PML instructions. Install the latest version.
Code: 040xxx
Description:
MIO Card Error
Code: 050000
Description:
The Line Sensor has problems finding the Mark Encoder.
Code: 060000
Description:
The Line Sensor is not functioning properly because there is too much ambient light.
Code: 060100
Description:
Incorrect Line Sensor type in the EEROM.
Code: 060200
Description:
Incompatible Firmware and Carriage PCA.
Code: 060300
Description:
Incompatible Firmware and Line Sensor.
Code: 060400
Description:
Incompatible Carriage PCA and Line Sensor OR Line Sensor not calibrated after replacing Carriage Assembly.
Code: 060500
Description:
Line Sensor not calibrated.
Code: 07xxxx
Description:
Firmware Error.
Code: 080001
Description:
Hard Disk Drive installed without PostScript.
Code: 08xxxx
Description:
PostScript Error.
Code: 090004
Description:
PostScript installed without the Hard Disk Drive.
Code: 09xxxx
Description:
Hard Disk Drive Error.
熱門圖文